找货询价

一对一服务 找料无忧

专属客服

服务时间

周一 - 周六 9:00-18:00

QQ咨询

一对一服务 找料无忧

专属客服

服务时间

周一 - 周六 9:00-18:00

技术支持

一对一服务 找料无忧

专属客服

服务时间

周一 - 周六 9:00-18:00

售后咨询

一对一服务 找料无忧

专属客服

服务时间

周一 - 周六 9:00-18:00

RX2A-434-64

型号:

RX2A-434-64

品牌:

RADIOMETRIX[ RADIOMETRIX LTD ]

页数:

5 页

PDF大小:

228 K

Radiometrix  
Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England  
Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233  
05 October 2009  
TX2H-4xx-64  
UH F H ig h P o we r FM Tr a n s mit t e r  
The TX2H is a 433/434MHz single-channel FM  
transmitter module with a power output of  
25mW nominal. It is a 100% pin-compatible  
drop-in replacement for the Radiometrix TX2  
and can be used to replace the TX2 in  
applications where greater radiated power is  
desired (for example when space limitations  
dictate the use of small and inefficient antennas,  
or in countries where the extra power is  
permitted). The module will handle raw data  
rates up to 64kb/s. The TX2H transmitter can be  
used with either RX2G or RX2A receivers.  
Figure 1: TX2H-433-64-5V & RX2A-433-64  
Features  
Standard frequencies: 433.92MHz and 434.42MHz  
Hi power drop in replacement for TX2  
Data rates up to 64kbps  
Usable range over 500m  
Fully screened  
Low power requirements  
Conforms to European EN 301 489-3 and ETSI EN 300 220-3 (for ERP 10mW)  
Conforms to Australian/New Zealand AS/NZS 4268:2003  
Instead of the SAW-based technology of the TX2, the TX2H uses a PLL circuit locked to a crystal for  
better frequency stability over a wider temperature range (-40C to +85C), at the expense of slightly  
slower power-up.  
The TX2H is available as standard on frequencies of 433.92MHz and 434.42MHz at 25mW power output,  
in either 3V(3.3V) or 5V versions. Custom frequencies may be available to order (consult factory). The  
module is designed to meet all applicable EMC and type approval requirements.  
The module can be made available if required in an extra-high-power version (TX2EH), in the same  
footprint and pinout but giving 90-100mW nominal output power at 5V supply with a current  
consumption of less than 45mA (DC to RF conversion efficiency better than 45%).  
Applications  
Handheld terminals  
Data loggers  
Industrial telemetry and telecommand  
In-building environmental monitoring and control  
High-end security and fire alarms  
Vehicle data up / download  
Technical Summary  
Size: 32 x 12 x 5.5mm  
Operating frequency: 433.92MHz and 434.42MHz  
Supply : 3V or 5V regulated  
Current consumption: 25mA typical  
Data bit rate: 64kbps max.  
Transmit power: +14dBm (25mW) nominal  
Evaluation platforms: Universal Evaluation Kit, NBEK + SIL carrier board  
sales@radiometrix.com TX2H – Data  
Page - 1 -  
Functional description  
The TX2H transmitter module is a crystal based PLL controlled FM transmitter operating on either 3V  
or 5Vsupply and is available in 433.92MHz.  
R1  
3
3V / 5V  
868/915 MHz  
band pass  
filter  
R2  
ref  
osc  
35kHz  
LPF  
64  
÷
amp  
buffer  
φ
2
5
TXD  
V C O  
RF out  
Loop  
Filter  
4
1
0V  
RF GND  
Figure. 2: TX2H block diagram  
User interface  
5.5 mm  
32 mm  
Ra diom e trix  
TX2H UHF Tra nsm itte r  
12.0 mm  
12.5 mm  
pin spacing:  
2.54 mm  
PCB level  
20.32 mm  
1
2
3
4
5
1 = RF gnd  
2 = RF out  
3 = Vcc  
4 = 0V  
5 holes of 0.7 mm dia.  
pin spacing 2.54 mm  
5 = TXD  
Figure 3: TX2H pin-out and dimension  
TX2H pin  
Name  
Function  
1
RFgnd  
RF ground, internally connected to the module screen and pin 4 (0V). This pin  
should be directly connected to the RF return path - e.g. coax braid, main PCB  
ground plane etc.  
2
3
RF out  
VCC  
50RF output to antenna. Internally DC-isolated.  
+ve supply pin. The module will generate RF when the Vcc supply is present.  
Max ripple content 0.1Vp-p. A 100nF de-coupling ceramic capacitor is  
suggested.  
4
5
0V  
TXD  
DC supply ground. Internally connected to pin 1 and module screen.  
This DC coupled modulation input will accept either serial digital data ( 0 V to  
Vcc levels) or high level linear signals. Input impedance is 100 kΩ  
sales@radiometrix.com  
TX2H – Data  
Page - 2 -  
Preliminary Specifications (TX2H-433-64-5V):  
Figures apply at +25°C, 3.0V or 5.0V supply as applicable, unless otherwise stated.  
Operating temperature range  
-40°C to +85°C  
Supply voltage (3V version)  
Supply voltage (5V version and TX2EH)  
Supply current  
2.5 - 3.5V (3.0V nominal, 4.0V absolute max.)  
4.5 - 5.5V (5.0V nominal, 6.0V absolute max.)  
25mA typical  
Supply current (for TX2EH version)  
Output power  
45mA typical  
+14dBm (25mW), ±1dB  
+20dBm (100mW), ±1dB  
33% approx.  
20% approx.  
45% approx.  
Output power (for TX2EH version)  
DC to RF conversion efficiency (3V version)  
DC to RF conversion efficiency (5V version)  
DC to RF conversion efficiency (for TX2EH)  
Harmonics/spurious emissions  
<-36dBm below 1GHz, <-30dBm above 1GHz  
(<-40dBm typical)  
Initial centre frequency accuracy  
Centre frequency variation over volts/temp  
FM deviation  
±15kHz max.  
±40kHz max.  
±30kHz typical  
Power-up time (DC on to full RF output)  
Baseband bandwidth  
1.1ms typical, 1.5ms max.  
DC-35kHz approx.  
Maximum raw data rate  
64kbps  
Required TXD input levels  
0V (logic 0), +5V (logic 1). Non-inverting.  
Product designations:  
TX2H-433-64-3V  
TX2H-433-64-5V  
TX2H-434-64-3V  
TX2H-434-64-5V  
TX2EH-433-64-5V  
TX2EH-434-64-5V  
(433.92MHz, 3V version)  
(433.92MHz, 5V version)  
(434.42MHz, 3V version)  
(434.42MHz, 5V version)  
(433.92MHz, 100mW version)  
(434.42MHz, 100mW version)  
Matching receivers  
RX2G-433-15-5V  
RX2G-433-64-5V  
RX2G-434-15-5V  
RX2G-434-64-5V  
(433.92MHz, 15kbps version)  
(433.92MHz, 64kbps version)  
(434.42MHz, 15kbps version)  
(433.42MHz, 64kbps version)  
RX2A-433-10  
RX2A-433-64  
RX2A-434-10  
RX2A-434-64  
(433.92MHz, 10kbps version)  
(433.92MHz, 64kbps version)  
(434.42MHz, 10kbps version)  
(433.42MHz, 64kbps version)  
sales@radiometrix.com  
TX2H – Data  
Page - 3 -  
Antenna requirements  
Three types of integral antenna are recommended and approved for use with the module:  
0.5 mm enameled copper wire  
close wound on 3.2 mm diameter former  
RF  
433 MHz = 24 turns  
A. Helical antenna  
Feed point 15% to 25% of total loop length  
track width = 1mm  
RF-GND  
4 to 10 cm2 inside area  
C2  
C1  
RF  
C3  
C4  
B. Loop antenna  
16.4cm  
wire, rod, PCB-track or a combination  
of these three  
RF  
433 MHz = 16.4 cm total from RF pin.  
C. Whip antenna  
Fig.8: Antenna  
A
helical  
**  
**  
***  
**  
B
loop  
C
whip  
***  
***  
*
Ultimate performance  
Easy of design set-up  
Size  
*
*
**  
***  
Immunity proximity effects  
*
A) Helical  
Wire coil, connected directly to pin 2, open circuit at other end. This antenna is very  
efficient given it's small size (20mm x 4mm dia.). The helical is a high Q antenna, trim the  
wire length or expand the coil for optimum results. The helical de-tunes badly with  
proximity to other conductive objects.  
B) Loop  
C) Whip  
A loop of PCB track tuned by a fixed or variable capacitor to ground at the 'hot' end and  
fed from pin 2 at a point 20% from the ground end. Loops have high immunity to  
proximity de-tuning.  
This is a wire, rod, PCB track or combination connected directly to pin 2 of the module.  
Optimum total length is 15.5cm (1/4 wave @ 433MHz). Keep the open circuit (hot) end  
well away from metal components to prevent serious de-tuning. Whips are ground plane  
sensitive and will benefit from internal 1/4 wave earthed radial(s) if the product is small  
and plastic cased  
The antenna choice and position directly controls the system range. Keep it clear of other metal in the  
system, particularly the 'hot' end. The best position by far, is sticking out the top of the product. This is  
often not desirable for practical/ergonomic reasons thus a compromise may need to be reached. If an  
internal antenna must be used try to keep it away from other metal components, particularly large ones  
like transformers, batteries and PCB tracks/earth plane. The space around the antenna is as important  
as the antenna itself.  
sales@radiometrix.com  
TX2H – Data  
Page - 4 -  
Radiometrix Ltd  
Hartcran House  
231 Kenton Lane  
Harrow, Middlesex  
HA3 8RP  
ENGLAND  
Tel: +44 (0) 20 8909 9595  
Fax: +44 (0) 20 8909 2233  
sales@radiometrix.com  
www.radiometrix.com  
Copyright notice  
This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or  
in part must give clear acknowledgement to the copyright owner.  
Limitation of liability  
The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the  
right to make changes or improvements in the design, specification or manufacture of its subassembly products  
without notice. Radiometrix Ltd does not assume any liability arising from the application or use of any product or  
circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the  
use of its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular  
application. These radio devices may be subject to radio interference and may not function as intended if interference  
is present. We do NOT recommend their use for life critical applications.  
The Intrastat commodity code for all our modules is: 8542 6000  
R&TTE Directive  
After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of the  
R&TTE Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance to the essential  
requirements specified in Article 3 of the Directive, as appropriate to the particular equipment.  
Further details are available on The Office of Communications (Ofcom) web site:  
http://www.ofcom.org.uk/radiocomms/ifi/  
Information Requests  
Ofcom  
European Radiocommunications Office (ERO)  
Peblingehus  
Riverside House  
Nansensgade 19  
2a Southwark Bridge Road  
London SE1 9HA  
Tel: +44 (0)845 456 3000 or 020 7981 3040  
Fax: +44 (0)20 7783 4033  
information.requests@ofcom.org.uk  
DK 1366 Copenhagen  
Tel. +45 33896300  
Fax +45 33896330  
ero@ero.dk  
www.ero.dk  
sales@radiometrix.com  
TX2H – Data  
Page - 5 -  
厂商 型号 描述 页数 下载

TE

RX2 电源PCB继电器[ Power PCB Relay ] 3 页

RADIOMETRIX

RX2-433 UHF FM数据发送器和接收器模块[ UHF FM Data Transmitter and Receiver Modules ] 15 页

RADIOMETRIX

RX2-433-14-3V UHF FM数据发送器和接收器模块[ UHF FM Data Transmitter and Receiver Modules ] 15 页

RADIOMETRIX

RX2-433-14-5V 超高频无线电遥测发射模块[ UHF Radio Telemetry Transmit Module ] 11 页

RADIOMETRIX

RX2-433-160-3V UHF FM数据发送器和接收器模块[ UHF FM Data Transmitter and Receiver Modules ] 15 页

RADIOMETRIX

RX2-433-160-5V UHF FM数据发送器和接收器模块[ UHF FM Data Transmitter and Receiver Modules ] 15 页

RADIOMETRIX

RX2-433-40-3V UHF FM数据发送器和接收器模块[ UHF FM Data Transmitter and Receiver Modules ] 15 页

RADIOMETRIX

RX2-433-40-5V 超高频无线电遥测发射模块[ UHF Radio Telemetry Transmit Module ] 11 页

RADIOMETRIX

RX2-433-40-B UHF FM数据发送器和接收器模块[ UHF FM Data Transmitter and Receiver Modules ] 15 页

RADIOMETRIX

RX2-433-40-TR UHF FM数据发送器和接收器模块[ UHF FM Data Transmitter and Receiver Modules ] 15 页

PDF索引:

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

0

1

2

3

4

5

6

7

8

9

IC型号索引:

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

0

1

2

3

4

5

6

7

8

9

Copyright 2024 gkzhan.com Al Rights Reserved 京ICP备06008810号-21 京

0.161240s