ALUMINUM ELECTROLYTIC CAPACITORS
4.5mmL Chip Type
UZS
UWX
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Smaller
High
UZT
UZS
Smaller
Temperature
UZR
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–40 to + 85°C
4 to 50V
1 to 220µF
+–20% at 120Hz, 20°C
After 2 minutes' application of rated voltage at 20°C leakage current is not more than 0.01 CV or 3 (µA) ,whichever is greater.
,
Measurement frequency : 120Hz at 20°C
4
6.3
10
16
25
35
50
Rated voltage (V)
Tangent of loss angle (tan δ)
0.50
0.30
0.24
0.19
0.16
0.14
0.14
tan δ (MAX.)
Measurement frequency : 120Hz
Rated voltage (V)
4
7
6.3
4
10
3
16
25
2
35
2
50
2
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
2
4
Impedance ratio
ZT / Z20 (MAX.)
15
8
8
4
3
3
+
Capacitance change
tan δ
Within 20% of the initial capacitance value
–
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 2000 hours at 85°C.
200% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
Shelf Life
Leakage current
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
+
Capacitance change Within 10% of the initial capacitance value
tan δ
–
Resistance to soldering
heat
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Leakage current
Marking
Black print on the case top.
Chip Type
Capacitance
Type numbering system (Example : 16V 10 F)
µ
Positive
1
2
3
4
5
6
7
8
9 10 11 12 13 14
U Z S 1 C 1 0 0 M C L 1 G B
Plastic platform
Voltage
Lot No.
C
0.2
0.3 MAX.
Taping code
(mm)
6.3
Configuration
φD
A
B
C
E
4
5
+
Capacitance tolerance ( 20%)
–
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
Rated capacitance (10µF)
Rated voltage (16V)
Series name
+0.1
–0.2
0.5 to 0.8
4.5
Negative
Voltage mark for 6.3V is 6V
.
Type
Dimensions
4
0G
6.3
0J
10
1A
16
1C
25
1E
35
1V
50
1H
V
Cap. (µF)
Code
010
1
2.2
3.3
4.7
10
22
33
47
100
220
4
8.4
13
17
20
33
2R2
3R3
4R7
100
220
330
470
101
221
4
4
5
6.3
4
5
6.3
6.3
16
27
42
52
4
5
6.3
18
29
46
4
5
6.3
6.3
23
37
49
58
4
5
5
6.3
28
37
45
70
5
5
6.3
33
41
52
4
4
5
6.3
28
33
56
96
Case size Rated
φ D(mm)
ripple
Rated ripple current (mArms) at 85°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UUR(p.154), UUG(p.160) if high C/V
products are reqired.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz or more
Please refer to page 3 for the minimum order quantity.
Coefficient
0.70
1.00
1.17
1.36
1.50ꢀꢀ
108
