ALUMINUM ELECTROLYTIC CAPACITORS
4.5mmL Chip Type, Bi-Polarized
ZP series
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
WP
Smaller
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Z P
Smaller
Specifications
ZE
Item
Performance Characteristics
Category Temperature Range –40 ~ +85°C
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
6.3 ~ 50V
0.1 ~ 47µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage leakage current is not more than 0.05 CV or 10 (µA) , whichever is greater.
,
Measurement frequency : 120Hz Temperature : 20°C
,
Rated voltage (V)
6.3
10
16
25
35
50
tan
δ
tan δ (MAX.)
0.30
0.24
0.20
0.18
0.16
0.16
Measurement frequency : 120Hz
6.3
4
10
3
16
2
25
2
35
2
50
2
Rated voltage (V)
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
8
8
4
4
3
3
After 2000 hours' application of rated voltage
at 85°C with the polarity inverted every 250
hours, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Within ±20% of initial value
300% or less of initial specified value
Initial specified value or less
Endurance
Shelf Life
Leakage current
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
Capacitance change
tan δ
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Resistance to soldering
heat
for 30 seconds. After removing from the hot plate and restored
at room temperature,they meet the characteristic requirements
listed at right.
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
1
2
3
4
5
6
7
8
9 10 11 12 13 14
U Z P 1 C 1 0 0 M C L 1 G B
Plastic platform
0.3 MAX.
Capacitance
C±0.2
Voltage
Lot No.
Taping code
(mm)
6.3
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
Configuration
φD
A
B
4
5
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
C
E
+0.1
–0.2
4.5
0.5 ~ 0.8
Voltage mark for 6.3V is 6V
.
Type
Dimensions
6.3
0J
10
16
25
35
50
V
Cap. (µF)
Code
1A
1C
1E
1V
1H
0.1
0.22
0.33
0.47
1
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
4
1.0
2.0
2.8
4.0
8.4
4
4
4
4
2.2
3.3
4.7
4
8.4
16
5
13
5
12
16
27
5
5
17
20
4
5
12
23
37
49
5
5
18
29
6.3
10
4
17
33
41
6.3
6.3
22
33
47
5
28
37
45
6.3
6.3
6.3
6.3
6.3
6.3
Rated
ripple
Case size
φD (mm)
Rated Ripple (mArms) at 85°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz~
1.50
Coefficient
0.70
1.00
1.17
1.36
Please select WP(p.47), UN(p.77) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V
