ALUMINUM ELECTROLYTIC CAPACITORS
4.5mmL Chip Type, Wide Temperature Range
ZT series
WT
Chip type with 4.5mm height, operating over wide temperature
range of –40 ~ +105°C
.
Smaller
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Z T
Smaller
Specifications
ZG
Item
Performance Characteristics
Temperature Range
Category
–40 ~ +105°C
6.3 ~ 50V
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
0.1 ~ 100µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan
δ
tan δ (MAX.)
0.38
0.32
0.20
0.16
0.14
0.14
Measurement frequency : 120Hz
Rated voltage (V)
6.3
6
10
10
5
10
16
3
6
25
3
6
35
3
4
50
3
4
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Capacitance
change
Within ±25% of initial value (16V or less)
Within ±20% of initial value (25V or more)
300% or less of initial specified value
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
Endurance
Shelf Life
tan δ
Leakage current Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for characteristics listed above.
endurance
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Resistance to soldering
heat
Leakage current
Marking
Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10 F)
µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Positive
105°C Marking
U Z T 1 C 1 0 0 M C L 1 G B
Capacitance
Lot No.
Plastic platform
Taping code
Voltage
0.3 MAX.
C±0.2
(mm)
6.3
Configuration
φD
4
5
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
A
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
B
C
E
+0.1
–0.2
4.5
Negative
Voltage mark for 6.3V is 6V .
0.5 ~ 0.8
Type
Dimensions
6.3
10
16
25
35
50
V
Cap. (µF)
0J
1A
1C
1E
1V
1H
Code
0R1
0.1
0.22
0.33
0.47
1
4
0.9
2.2
2.8
3.3
5.4
9.6
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
4
4
4
2.2
3.3
4.7
4
4
12
4
11
20
33
42
4
13
22
36
5
16
26
10
4
16
5
5
6.3
22
33
4
19
5
5
24
30
40
5
26
35
44
6.3
6.3
6.3
5
5
26
32
52
6.3
6.3
47
6.3
Rated
ripple
Case size
φ D (mm)
100
6.3
Rated Ripple (mArms) at 105°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are
given in page 25, 26.
Please select UX(p.74), UJ(p.76) series if high C/V
products are reqired.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz~
1.50
Coefficient
0.70
1.00
1.17
1.36
Please refer to page 3 for the minimum order quantity.
CAT.8100V
