ALUMINUM ELECTROLYTIC CAPACITORS
3.0mmL Chip Type
ZD series
Chip type with 3.0mmL height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
ZR
Smaller
Z D
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–40 to +85°C
4 to 25V
2.2 to 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
,
Rated voltage (V)
tan δ (MAX.)
4
0.50
4
6.3
0.40
6.3
4
10
0.30
10
3
16
0.24
16
2
25
0.19
25
2
120Hz 20°C
Tangent of loss angle (tan δ)
Rated voltage (V)
120Hz
Stability at Low
Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
7
Impedance ratio
ZT / Z20 (MAX.)
15
8
8
4
4
Capacitance change
tan δ
Within ±30% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 85°C.
Endurance
Shelf Life
Leakage current
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at
20°C, they shall meet the specified values for the endurance characteristics listed above.
Capacitance change
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
The capacitors are kept on a hot plate for 30 seconds, which is maintained at
250°C. The capacitors shall meet the characteristic requirements listed at
right when they are removed from the plate and restored to 20°C.
Resistance to
soldering heat
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
Positive
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Voltage (C : 16V)
Plastic platform
0.3 MAX.
Series
C±0.2
Lot No.
U Z D 1 C 1 0 0 M C L 1 G B
Taping code
Configuration
(mm)
6.3
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
φD
A
4
5
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
B
C
E
+0.2
–0.1
Capacitance
Voltage
3.0
Negative
0.5 to 0.8
V
4
6.3
10
16
C
25
Type
Code
g
j
A
E
Dimensions
4
6.3
10
16
25
V
Cap. (µF)
2.2
0G
0J
1A
1C
1E
Code
2R2
4
7
11
16
18
20
27
3.3
3R3
4R7
5R6
6R8
100
220
330
470
101
4
4.7
4
5.6
5
6.8
5
10
5
23
37
6.3
22
4
20
28
33
56
5
28
5
33
41
6.3
33
5
5
37
45
70
6.3
47
5
6.3
6.3
Case size
φD (mm)
Rated
ripple
100
6.3
Rated ripple current (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Taping specifications are given in page 23.
Recommended land size soldering by reflow are given
in page 18,19.
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz or more
1.50
Coefficient
0.70
1.00
1.17
1.36
Please refer to page 3 for the minimum order quantity.
CAT.8100C
